steering knuckle发音

意思翻译

转向关节

相似词语短语

steering───n.操纵；指导；掌舵；v.驾驶；掌舵（steer的ing形式）

knuckle cracking───[医]指节断裂；折手指

moose knuckle───驼鹿关节

steering wheel───n.方向盘; 驾驶盘；方向盘；[车辆]驾驶盘；舵轮

steering committee───n.筹划指导委员会

knuckle dusters───关节掸子

steering columns───n.（车辆的）转向柱，方向盘柱；n.驾驶杆( steering column的名词复数 )

steering locked───转向锁定

knuckle sandwich───n.对准嘴的一拳

双语使用场景

Thus, the steering knuckle, spindle, wheels, and tires turn to one side, causing the car to turn.───这样，转向节、转向节轴端、车轮和轮胎都会向一侧旋转，汽车实现转向。

This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle.───这一运动是由装在驾驶员前面的转向盘与转向节之间的转向器和连杆装置来共同完成的。

The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle.───结果表明，锻造余热淬火工艺对汽车转向节质量有明显改善。

The steering-knuckle arm, attached to the front wheels, are therefore forced to swing the wheels to the right or left on their pivots.───于是，与前轮相连的转向节臂使车轮在其轴线上左右转动。

The trike frame should now be nearing completion and only requires the installation of the steering knuckle mounting plates to be complete.───该三轮车框架现在应该已接近完成，只需要安装指导安装板的关节完整。

Assuming that the Knuckle Face Plates have been fabricated (and welded to the frame), the steering knuckle assembly can now be assembled.───假设猪脚面板已制造（和焊接到框架）中，转向节大会，现在可以进行组装。

The last modification required to the brake faceplate, is making the plate flush with the steering knuckle faceplate.───最后修改面板所需的制动，转向是使板与关节冲洗面板中删除。

A feasible process scheme was made for forming the steering knuckle of a truck based on a technological analysis on the forging of the part.───通过对卡车转向节锻件的工艺分析，制定了合理的工艺方案。

These include the fabrication of the Derailleur Cable Stop, and drilling the holes for both steering knuckle levels.───这些措施包括停止生产的变速器电缆，钻两个孔，关节指导的水平。

英语使用场景

Remove the steering knuckle from the strut.

A worn steering knuckle arm on a motor vehicle may cause heavier steering operation, the reasons are studied in this paper according to the steering trapezium principle.

Place the entire steering knuckle assembly in a vise and re - drill using the # Q drill bit.

Route sensor wire from steering knuckle to fender panel.

Lots of well-forged, normatively heat-treated, and elaborately-processed steering knuckle arms, pitman arm, idler arm pendulum lever etc, can be used widely as parts of various types of truck and car.

The steering knuckle then supported through Ball joints, by upper and lower control arms which are attached to the car frame.

Sentencedict.com try its best to gather and create good sentences.

With the steering gear meshing steering rack level arrangement, the both sides with change the steering knuckle tie rod through a ball place to be connected.

A steering knuckle is the key component in cars, which needs high requirements in dimensional accuracy and product quality.