steam injection发音

意思翻译

蒸汽喷射，蒸汽注入；射汽法

相似词语短语

steam───adj.蒸汽的；n.蒸汽；蒸汽动力；水汽；精力；vi.冒水汽；蒸；用蒸汽动力推动；疾行；<非正式>开始战斗；抢劫

alegar injection───阿莱加注射液

amnios injection───羊膜注射

cash injection───资金注入

direct injection───直接射油，直接注入；[动力]直接喷射；直接注入；直接射出法

corticosteroid injection───皮质类固醇注射

dependency injection───依赖注入

injection mold───[塑料]注塑模具

administering injection───注射给药

双语使用场景

Therefore, steam injection parameters for Nine-7 Block were analyzed and optimized using orthogonal experiment design.───为此，利用正交试验设计方法对九7区注汽工艺参数进行了敏感性分析和优化。

Under the production condition of steam injection, the energy ratio can reach 7.0.───注入蒸汽开采初始条件下，能量效率可以达到7.0。

Method Steam injection development and well pattern of horizontal Wells were studied by using numerical simulation.───方法利用数值模拟方法，对水平井注蒸汽的开发、布井方式等进行研究。

Steam injection, among the oldest heat-based methods, was decisive in the revival of the Kern River Oil Field back in the early 1960s.───加热是历史最悠久的方法，其中蒸汽注入法是1960年代初期让美国克恩河油田重现生机的决定性因素。

This relationship can be used to determine steam injection volume and the production distribution during steam stimulation.───利用这一线性关系，以油藏的油汽比确定注汽量，可解决稠油蒸汽吞吐阶段的配产问题；

At benefit-oriented present, one of the key issues related to the cost of steam injection is the on - off of steam - water separators.───在重视效益的今天，如何对待高压汽水分离器的关停，也是关系到注汽成本的一个关键问题。

The results show that high thermal stress is generated in casing at the beginning of steam injection.───分析结果表明，注汽初始阶段套管内会产生较大的热应力；

Close to end of exploiting period of heavy oil, it's usually adopting separate steam injection for enhancing oil recovery effectively.───在稠油开采的后期，为了有效提高采收率普遍采用分层注汽的生产方式。

The steam-injection boiler is the important equipment in producing viscous oil, and is the main energy consumption facility.───油田注汽锅炉是油田稠油开采的重要设备，又是油田的主要耗能设备。

英语使用场景

The level of oil production using steam injection technique directly depends on the heat efficiency of steam injection, and the heat efficiency can be determined by injection-production parameters.

Used the hot cyclic steam injection craft mining thick oil is the thick oil development main form.

A model for optimizing the steam injection process in thermal recovery wellbore is developed and solved with enumeration method under two kinds of conditions, namely steam soak and steam flooding.

The study shows that cyclic steam injection rate, soaking time, flowing bottom hole pressure and blowdown mode are important factors influencing the effectiveness of single well steam stimulation.

The sensitivity analysis indicates that the parameters impacting the production results from high to low are production time, steam dryness, cyclic steam injection volume, steam injection pressure.

Intermittent steam injection can increase the specific volume, swept volume and utilization ratio of heat, and can improve formation of seepage in oil reservoir so as to improve flooding effect.

Major factors which influence the steam injection profile are steam overlaying and high-permeability zones during steam flooding and cyclic steam injection.

The experiment shows that nitrogen and steam injection is beneficial for increasing the effect of oil well stimulation.

The method can be used to calculate the thermodynamic properties of the moist combustion gas for any kind of hydrocarbon fuel, any steam injection ratio and any fuel coefficient.