metal flow发音

意思翻译

[机]金属流动

相似词语短语

flow───vi.流; 垂; 流出; （谈话、文体等）流畅；n.流动；生产，供应；车流；流量；传播；流通；滔滔不绝；连贯，流畅；涨潮；泛滥；（苏格兰）湿地，沼泽；月经；vt.使泛滥; 淹没; 排出；n.流动; 滔滔不绝; 涨潮; 连贯；v.（使）流动，涌流；流通；传播；流畅；充满；大量供应；涨；涨潮；川流不息；飘扬；来自，由……产生；来月经；（矿物、岩石等）变形；n.(Flow)（美）弗洛（人名）

metal───vt.以金属覆盖；n.（Metal）（捷、瑞典）梅塔尔（人名）；n.金属；合金；adj.金属制的

ceaseless flow───源源不断的流动

cohesive flow───粘性流

flow controller───[自]流量控制器

current flow───电流

flow about───流动

flow production───流水线生产；大规模生产

flow diagram───n.流程图，作业图，生产过程图解; 框图；[工业]流程图；作业图

双语使用场景

The results indicate that the metal flow curve wavily fluctuates.───结果表明，金属流动曲线起伏很大。

And calculate the equation in compensation amount of probing into the metal flow of more detailed description.───并较详细的描述探讨了金属流量的补偿量计算方程。

and metal flow in steel tube during sizing process were analyzed.───分析了定径过程中钢管内金属流动和弹复行为。

Coining is usually done on surfaces parallel to the parting line, and little metal flow is involved in the operation.───铸币通常是做表面平行的线，与小金属流动是参与行动的。

Metal flow of lead screw cold roll-beating process is analyzed, and metal flow's law of minimum resistance is verified.───分析了丝杠冷滚打过程中金属的流向，验证了金属流动最小阻力定律。

This flexibility accommodates any process, maintenance, or emergency metal flow direction to be achieved.───这样的灵活性使得任何过程，维护或紧急状态下的金属流动方向都能够达到。

Through the simulation, the rules of velocity field deformation area distribution and metal flow have been obtained.───通过三维有限元模拟辗环轧制过程，得到了轧制过程中的变形区速度场分布以及金属流动规律；

The investigation showed that metal flow during the upsetting is different from continuous motion of deformation units fined by finite . . .───试验证明，在镦粗过程中金属的流动并不是有限元解出的变形单元的连续移动。

Metal flow takes place within the plastic range of the metal, so that the bend retains a permanent set after removal of the applied stress.───金属的流动发生在金属的塑性变形范围之内，因此在施加的外力去除之后弯曲保持永久的变形。

英语使用场景

During the friction stir welding process of aluminium alloy, the plastic metal flow in the weld is a kind of single-phase flow.

The experiments show that using UBET to Simulate the laws of the metal flow in drop forging was available.

The metal flow during indirect extrusion is analyzed, and the influence of billet machining on the quality of aluminium tube is also investigated.

On the basis of experiment and change of metal flow line, metallographic structure and micro-hardness in deformation zone, this paper researched process, characteristic and mechanism of fine-blanking.

The air entrapment of the liquid metal flow in the shot sleeve during the slow shot phase is one of the factors resulting in this kind of defect.

The liquid metal flow during mould filling in bottom gating system and its influence on the casting quality are introduced emphatically .

The results show that both gas-forming property and decomposition latent heat of the polystyrene material influence the metal flow velocity and the gaseous pressure of the gap significantly.

Compared with raw material, the cup formed by the technology of warm forming has perfect metal flow lines and the body's hardness and tensile strength are g...

For the defects such as dead zone and shrinkage cavity in conventional extrusion process, an inner cone punch was proposed to improve the metal flow behavior.