mass flow rate发音

意思翻译

[流]质量流率

相似词语短语

flow rate───流量; 流率；[流][水文]流量；[流]流速

volumetric flow rate───体积临；[流]容积流率

proportional to flow rate───与流量成比例

flow───vi.流; 垂; 流出; （谈话、文体等）流畅；n.流动；生产，供应；车流；流量；传播；流通；滔滔不绝；连贯，流畅；涨潮；泛滥；（苏格兰）湿地，沼泽；月经；vt.使泛滥; 淹没; 排出；n.流动; 滔滔不绝; 涨潮; 连贯；v.（使）流动，涌流；流通；传播；流畅；充满；大量供应；涨；涨潮；川流不息；飘扬；来自，由……产生；来月经；（矿物、岩石等）变形；n.(Flow)（美）弗洛（人名）

rate───n.(Rate)人名；(法、塞)拉特；n.比率，率；速度；价格；等级；vi.责骂；被评价；vt.认为；估价；责骂

mass───n.块，团；群众，民众；大量，众多；质量；vt.使集合；adj.群众的，民众的；大规模的，集中的；vi.聚集起来，聚集

ceaseless flow───源源不断的流动

cohesive flow───粘性流

flow controller───[自]流量控制器

双语使用场景

Experiments were carried out to the research on mass flow rate measurement using vortex flowmeter.───利用差压原理进行质量流量测量的方法进行实验研究。

With increase of mass flow rate, solid-gas ratio increases first and then decreases.───随着煤粉的输送流量的增大，固气比先增大后减小。

The numerical results comprehensively describe the influence of the slip boundary condition on mass flow rate.───数值分析结果给出了速度滑移边界条件对管道质量流量的影响。

The mass flow rate of the molten metal is controlled by means of a choke element fitted in the casting trough.───熔融金属的质量流率借助配合在浇注槽内的一个扼流元件控制。

Experimental results manifest that this method is feasible and effective for mass flow rate measurement.───结果表明，该测量方法结构简单，是测量质量流量的有效方法。

However, the rate of decrease in cooling water exit temperature decreases with an increase in air mass flow rate and spray water rate.───随着空气质量流量和喷淋水量的增加，冷却水出口温度降低，但是变化斜率逐渐减小，即存在着一最佳喷淋水童和空气质量。

However, in this case it is easier to use a mass flow rate because referring to a hippo feed rate in terms of moles is impractical.───然而，在这种情况下这是更容易使用一个质量流率，因为指从河马喂入痣的不切合实际。

The results show that the system runs steadily when the driving flow mass flow rate equals to the diffuser outlet vapor flow mass flow rate.───结果表明，当工作流流量同扩压段出口蒸气流量相等时系统能够稳定运行。

Also, note that the mass flow rate value is recalculated from the velocity or volume flow rate value specified on an opening.───同时，注意到率值从在一开放上指定的速度或者量流量值被重新计算的大规模的流动。

英语使用场景

Mass flow rate of added fuel, injecting location and physical throat area on rocket ejector performance were investigated.

Higher heat transfer rate as air mass flow rate increases.

The effects of the packing factor, working fluid mass flow rate on the thermal efficiency and electric gain were investigated, and the optimization of design parameters have been found in this paper.

The mass flow rate varies with the inner diameter and the length of adiabatic capillary tubes, the degree of subcooling and the condensing temperature were investigated.

Adiabatic combustion temperature at various oxidizer mass flow rates and grain length is obtained by thermodynamic calculation and has a maximum as oxidizer mass flow rate increases .

The relation between mass flow deviation and setting angle, flow pattern, liquid apparent mass flow rate is analyze based on the theory of two-phase flow.

The capillary tube model in subcooling single-phase region and two-phase region was established, and the difference of mass flow rate is within 10% between the predicted and the measured values.

The control properties of vortex valve for mass flow rate are numerically simulated.

With increase of mass flow rate, solid - gas ratio increases first and then decreases.