bearing load信息详情
[机]轴承负荷
bearing───n.[机]轴承；关系；方位；举止；v.忍受（bear的ing形式）
load───vi.[力]加载；装载；装货；vt.使担负；装填；n.负载，负荷；工作量；装载量
risking bearing───[经]风险负担；危险负担
graceful bearing───风采；风度翩翩；风姿；峬峭
bearing units───轴承单元
antifriction bearing───[机]减摩轴承；滚动轴承；减摩轴承，抗摩轴承; 滚动轴承
spherical bearing───球面轴承，球形支座，球面支承；[机]球面轴承；球面支承；[建]球形支座
bearing puller───轴承拆卸器；轴承拉出器，轴承拆卸工具
bearing down───下坠力；[医] 下坠感（盆腔内），分娩时屏气
It studies also the feasibility of this way for on-line monitoring bearing load of turbine generators.───研究测轴承支承力法对大型汽轮发电机组轴承负荷在线监测的可行性。
in plane finite element calculation the bearing load must be transformed into force of nodal.───在平面有限元计算中，必须把轴承负荷转为节点力。
The ultimate bearing load of the pile is used to calculate its buried depth.───桩的极限承载力来计算桩的入土深度。
If transition at the shaft collar of a circular shaft adopting closed angle will bring biggish stress concentration as bearing load.───圆轴轴肩处若采用尖角过渡，承载时将引起较大的应力集中。
In crowd- pile foundation design, the general idea thinks all the load bearing by piles and not considering the interpile soil bearing load.───群桩基础设计通常不考虑极间土承担荷载，认为荷载全部由极承担。
The value and direction of the static steam force change a lot in different performance cases, which change bearing load directly.───不同工况下汽流力的大小和方向会发生改变，直接影响轴承载荷。
If the actual load is a combined radial and axial load , then an equivalent static bearing load must be calculated .───如实际负荷为径向和轴向复合负荷，则必须计算当量轴承静负荷。
In fact that hull girder deflection could greatly affect the bearing load, so the calculation must take it into consideration.───结果表明，船体变形对各轴承负荷的影响很大。
The maximum load that can occur on a bearing should be used in the calculation of the equivalent static bearing load .───除径向负荷外，此类轴承还能承受一定的轴向负荷（见“当量轴承动负荷”）。
Planar bearing load cell designed particularly is used to alarm for travelling crane overload.
The article introduces the method of checking the bearing load by jack-up test after shafting alignment and illuminates the jack-up test with its application examples in a 1000 TEU container vessel.
Producing little stretch distortion and having no flection under permitted air speed and pressure are the criterions of assessing air conduit capacity based on its bearing load.
A new method is proposed to determine the excited torque and bearing load of the injection pump camshaft by means of measuring the longitudinal strain in the bottom part of the plunger.
Based on the experimental study on the cold-formed steel unlipped channels under concentrated bearing load, the feasibility about Perry formula applied in cold-formed steel structures is analyzed.
In the thesis studying measure methods of bearing load, include of strain gauge and jack - up method.
If transition a circular shaft adopting closed angle will bring biggish stress concentration as bearing load.
Instance of static loading test of 30m T beam, actual stress and deflection of structure tested is analyzed and capacity of bearing load for structure tested is evaluated.