finishing cut发音

意思翻译

精加工

相似词语短语

finishing───v.完成；结束；（竞赛）获得（名次）；用完，吃光（finish的现在分词）；n.得分的表现和技巧；（非正式）最后的修整

finishing touches───n.最后润色; 收尾工作；n.最后润色；收尾工作

finishing touch───最后一触，最后一笔；最后润色

finishing line───（赛跑的）终点线；n.精整作业线，终点线

cut cut───切，切

finishing nails───精整钉子

finishing lines───终点线，终航线；n.精整作业线，终点线( finishing line的名词复数 )

surface finishing───表面精加工，表面修整

cut───v.割破；（用刀等）切下，割成；剪短；释放；剪裁；削减；删节；剪切；停止做；断绝（关系）；剪辑；切换画面；旷（课）；伤害；切牌；相交；劈出（通道）；录制（音响）；adj.缩减的；割下的；雕过的；n.切，割；伤口；开口；削减；理发；（服装等的）式样；（钱的）份额；删节；割下的肉；伤害的话（或行为）；（场景）切换；（比赛）半程；切球；乐曲；剪辑；河道

双语使用场景

new WEDM (Wire Electrical Discharge Machining) technology for finishing cut has been developed, in which gas has been used as a dielectric instead of water.───用气体介质代替液体介质，开发出了一种新型的电火花切割精加工工艺。

There are two kinds of cuts in machine- shop work called, respectively, the "roughing cut" and the "finishing cut".───机械工厂的切削加工有两种，分别称为“粗切削”和“精切削”。

Generally speaking, bars of steel, forging, castings, etc. are machined to the required shape and size with only one roughing and one finishing cut.───一般地说，钢质棒料、锻件、铸件等只经一次粗切削和一次精切削即可达到所要求的形状和尺寸。

A roughing cut is usually to be followed by a finishing cut .───粗切削之后通常要精切削

the finishing cut , to make the work smooth and accurate , is a finer cut.───精切削是使工件表面光滑、尺寸准确，因而是一种更精细的切削。

Numerical simulation of surrounding rock stability of finishing cut in fully mechanized top coal caving───综放收尾切眼围岩稳定性数值模拟

Stability Analysis and Support Study on Surroundings of Finishing Cut───收作眼围岩稳定性分析与支护技术研究

A Method of finishing cut in deeply inclined caving face with single hydraulic props───大倾角放顶煤单体面收作方法新探

Finishing Cut Method of End-mining in Plow Mining Face───刨煤机工作面末采收尾方法

英语使用场景

Generally speaking, bars of steel, forging, castings, etc. are machined to the required shape and size with only one roughing and one finishing cut.

A new WEDM(Wire Electrical Discharge Machining) technology for finishing cut has been developed, in which gas has been used as a dielectric instead of water.

By means of finishing cut the trackless rubber-tried vehicle can directly go to the working face to remove the equipment.

Also, in some jobs, fot example, when great accuracy is not needed, or when a comparatively small amount of metal must be removed, a finishing cut may be all that is required.

The stability of the surrounding rock masses of finishing cut is analyzed systemically and its support design is optimized by numerical simulation with RFPA2D.

The removal speed of the fully-mechanized coal face with topped caving (FCFTC) can be increased by pre-excavating finishing cut on terminal mining line.

Because the finishing cut is continuously affected by the abutment pressure in front of the face, its maintenance is much more difficult than that of the ordinary coal entry.

There are two kinds of cuts in machine- shop work called, respectively, the "roughing cut" and the "finishing cut".