filling process发音

意思翻译

填土工作

填充过程

相似词语短语

filling───n.(Filling)人名；(瑞典)菲林；n.填充；填料；v.填满；遍及（fill的ing形式）

filling machine───灌装机；[食品]充填机；锉锯机；装料机; 灌注机器; 充填机械; 加料机

filling stations───汽车加油站（等于gasstation）

filling into───填充

filling up───填补；装满；堵塞；[机] 埋乞法; 装满

dental filling───补牙

filling date───交发日期；申请日；交发日期，填写日期

fuel filling───加油；加注燃油；填充燃料

filling pieces───填充件

双语使用场景

The final step of the filling process is to use acrylic glazing compound to fill minor surface flaws.───最后的步骤用丙烯酸釉填充表面的裂缝。

You must know how to stop the cylinder-filling process in case of an emergency.───你必须清楚在紧急的情况下如何停止气瓶的充装。

You must know how to stop the cylinder filling process in case of an emergency.───你必须知道在紧急情况下，如何停止气瓶的充装。

To be used cans have to be completely sealed with automatic sterilization. Foreign matters cannot pollute during tank filling process.───使用的罐装设备是全封闭自动杀菌的，罐装过程中异物不可能污染。

A threedimensional mathematical model of the resin transfer molding(RTM) filling process for the automobile bumper was presented.───首先建立了汽车保险杠树脂传递模塑充模过程的三维数学模型；

The filling process, solidification process and air entrapment condition of the aluminum casting were shown by numerical simulation.───通过数值模拟的方法对该铸件的充型过程、凝固过程及铸件的气体卷入情况进行模拟。

A low viscosity fluid without chemical reaction was used in this study to simulate the mold filling process in cold state during RIM.───本文采用无化学反应的低粘度流体进行RIM充模过程的冷态模拟研究。

Actually this pre-formed pouch has got its final volume before filling and will not not be deformed during filling process.───其实这预成型袋已得到填补之前的最后一卷，也不会不灌装过程中变形。

Documented skill prerequisites for filling process roles and responsibilities, and evidence that assigned staff meet these criteria.───为安排执行过程的角色和职责而文档化的技能先决条件，并且根据这些文档来分派人员看到这些标准。

英语使用场景

The origination and location of shrinkage porosity(hole)in the rudder horn was described by simulating the filling process of large pelagic cast-steel rudder horn using a CAE software.

Computer simulation was employed to optimize filling system to predict filling process and prevent the defects for Al alloy automotive parts in semi-solid die casting.

The molding filling process is a very important phase in RTM.

The filling process, microstructure and mechanical properties of A 357 alloy was studied by low pressure casting.

According to the force analysis of seeds during filling process, the calculation formulas for ultimate filling angle and falling angle of seed on scoop side were established.

Numerical simulation technology has been carried out to analyze the filling process of an aluminum alloy wheel produced by low pressure die casting.

Result shows that sediments transportation and filling process is controlled by fault terrace zone and accommodation zone formed by the major fault in structural transfer zone.

The filling process of the 12150 V diesel engine block casting was studied using finite element.

The effect mechanism of vacuum on the filling process was discussed. It shows that the vacuum can reduce the gas counterpressure in the casting mould cavity and improve the filling ability.