cylinder valve信息详情
[机]汽缸阀；气瓶阀
cylinder───n.圆筒；汽缸；[数]柱面；圆柱状物
oxygen cylinder───储氧筒，氧气瓶；氧气瓶；储氧筒
circumscribing cylinder───外切圆柱
cylinder head───[机]气缸盖
armorack cylinder───军械架筒体
pneumatic cylinder───气缸，气压缸
actuating cylinder───[机]作动筒；[动力]主动油缸；制动气缸；作动筒; 主动筒; 动力气缸; 主动油缸
valve───vt.装阀于；以活门调节；n.(Valve)人名；(俄、芬)瓦尔韦；n.阀；[解剖]瓣膜；真空管；活门
master cylinder───[机]主缸；制动缸；控制缸；主缸; 主油缸; 控制缸
When returning cylinders to the supplier, properly close the cylinder valve, replace and secure any valve outlet seals, and properly install the cylinder cap.───返还给供应商时，正确关闭钢瓶阀门，替换并固定阀门排气口密封，正确安装钢瓶帽。
Close the cylinder valve.───关闭钢瓶阀门。
Always close the cylinder valve when product delivery is NOT needed. Do NOT leave it open when the equipment is unattended or NOT operating.───当不需要产品输出时，总是关闭钢瓶阀门。当设备无人照管或没有运转时，不要让阀门开着。
Leaks occurring at the cylinder valve's pressure relief device, diaphragms, or valve to the cylinder connection cannot be repaired.───发生在钢瓶阀门的减压装置、横膈膜或阀门到钢瓶的接头处的泄露不能维修。
At the end of the shift or work day, close the cylinder valve and bleed the pressure off the regulator and torch equipment.───在下班或工作日结束的时候，关闭钢瓶阀门，放出调整器和吹管设备内的压力。
Always pressurize a regulator slowly, while standing with the cylinder valve between you and the regulator.───总是站得使钢瓶阀门位于你和调整器之间，对调整器慢慢加压。
The cylinder valve is equipped with a dip tube that, depending on orientation, will allow either gas or liquid withdrawal.───钢瓶阀门配备有汲取管。根据定位，可以提取气体或液体。当阀门排气口面朝上时，可以提取蒸气。
Always ensure that cylinder valve is closed, outlet seal is installed gas-tight, and protective cap is in place before shipping.───在运输之前，总是确保钢瓶阀门关闭、排气口密封安装正确和保护帽在正确的位置。
Always ensure that cylinder valve is closed, outlet seal is installed gas-tight, and protective cap is in place before shipping.
Once the piston is at the bottom of the cylinder, valve 3 is closed and valve 2 opened.
Check the cylinder valve for evidence of damage or contamination.
Safety Valve, Ball Valve, Needle Valve, Y - Control Valve, Y Cylinder Valve, Check Valve Cock.
Recommended Closing Procedure: Close the cylinder valve tightly using a gloved hand.
Recommended Closing Procedure: Close the cylinder valve tightly using a gloved hand. Always wearing gloves when operating cylinder valves. NEVER use wrenches or other persuaders to operate the valve.
Always pressurize a regulator slowly, while standing with the cylinder valve between you and the regulator.
Recommended Closing Procedure: Close cylinder valve tightly using a gloved hand.