coating layer发音

意思翻译

[涂料]涂层

相似词语短语

coating───v.给…穿上外衣；盖上（coat的ing形式）；n.涂层；包衣；衣料

layer───vt.把…分层堆放；借助压条法；生根繁殖；将（头发）剪成不同层次；n.层，层次；膜；[植]压条；放置者，计划者；vi.形成或分成层次；[植]通过压条法而生根

coating buffer───涂层缓冲液

coating thickness───[电] 涂膜厚度

conformal coating───保形[角]涂料；敷形涂料；保形涂层，保形涂敷

seed coating───[植]种皮

multi coating───n.多层镀膜

erbia coating───erbia涂层

milky coating───乳白涂层

双语使用场景

results) reveal that the coating layer of aluminum hydroxide is loose and porous.───结果表明，氢氧化铝所形成的包覆层是疏松和多孔的。

The properties of coated paper are mostly depended on the coating layer structure.───涂布纸或纸板的涂布性能受涂层结构的特性影响较大。

Exothermic efficiency, metallographical structure and transition region of coating layer were also investigated.───还研究了放热效应，金相组织与涂层过渡层。

It was found that there was no reaction between coating layer and aggregate through SEM studies on interfacial transition zone.───通过扫描电镜观察再生粗骨料的界面过渡区，发现涂浆层不与骨料本身反应。

For test specimens produced in a laboratory, the thickness of each paint coating layer must be recorded and indicated in the test report.───在试验室内制作的测试样品，每一片的厚度须记载并在测试报告中指明。

and a lead conductor coated with an insulating coating layer and a sealed vessel which are for use in this electrical part, etc.───以及密封容器和具有绝缘覆盖层的导线导体，两者都可以用在电气部件等中。

Thus, one coating layer is formed on the surface of the touch control plate so as to obtain thin touch control plate with high strength.───因此，在触控板的表面形成披覆层，从而实现其薄型化及高结合强度高的效果。

Through experimental comparison, the new process method can significantly improve the contact fatigue life of the coating layer.───通过实验对比，这种新工艺方法可以显著地提高涂层的接触疲劳寿命。

The film has obvious redshift phenomenon and its euphotic rate reduces with the increases of the number of coating layer.───镀膜层数增加，薄膜有明显红移现象并且透光率会降低。

英语使用场景

The coating layer of metal-organic compound consists of pulverulent metal, inorganic salt and organic compound liquid.

The mechanism of metal penetration defect of iron castings in EPC process has been analyzed, which arise from cracking of the coating layer.

The (results) reveal that the coating layer of aluminum hydroxide is loose and porous.

Mechanism of low gloss- producing, structure of coating layer, manufacture and development of matte and dull coated paper were described.

A coating layer can be prepared outside the pastille coating layer.

The homogeneity of the coating layer was characterized by SEM and EDX.

A continuous and uniform nickel coating layer has been obtained on thesurface of carbon fiber (CF) and flake graphite (FG) by electroless platingtechnique.

Compared with that of furan resin bonded sand, the feasibility of phenol resin bonded sand in forming a uniform coating layer in the inside mould surface is studied as well.

The strength of coating layer obtained by - shot - felt powder with subsonic oxygen - acetylene spraying technique was discussed.