winding process发音

意思翻译

绕制法

相似词语短语

winding───adj.蜿蜒曲折的；v.蜿蜒而行；缠绕；卷绕；被弯曲；环绕（核心）；给（钟表等）上发条；转动（钥匙、把手）；（使）（录像带、录音带等）倒退（或前进）；（用绞车等）吊起（某物）；（使）气急；轻拍后背使（婴儿）打嗝；嗅出（人或动物的）气味；（诗、文）吹（号角）（wind的现在分词）；n.卷绕；线圈；蜿蜒曲折的路径；n.(Winding)（美）温丁（人名）

winding river───（美）风河系统公司；温德河（美国怀俄明州河流）

armature winding───[电]电枢绕组

winding stairs───螺旋式楼梯

winding trip───绕组跳闸

winding trail───蜿蜒的小径

winding up───清算；停业清理；清理; 结业

winding road───连续弯路；弯曲路

filament winding───纤维缠绕；灯丝绕阻；[电子]灯丝电源绕组

双语使用场景

tension control is the key technique in the filament winding process to guarantee the product quality.───纤维缠绕中张力的控制是关系到产品质量的关键技术。

This UP resin is a high performance and chemical resistant resin which is suitable for winding process.───该树脂为优良的耐化学树脂，并适合缠绕成型的工艺要求。

mould, gel coat formulation and winding process of high performance FRP electric insulating tube were summarized.───本文介绍了玻璃钢高强电绝缘管的模具、胶液配制及缠绕成型工艺。

and the micromotor is also provided with an independent control unit, and can independently control the whole wire winding process.───微电机还设置有独立的控制单元，可以单独控制整个绕线过程。

Clearing yarn parameter should be set rationally in winding process.───络筒合理设定清纱参数；

In the literature, this impact of there winding process on stray load loss has never before been reported.───在该文献中指出，重绕工艺对漏磁负载的影响（冲击），以前从来没报道过。

The stable negative-pressure system can effectively grab the yarn to make the winding process running properly.───恒定的吸风负压使纱线能够有效地被吸附，使络筒工序能够平稳地进行。

A non-contact dynamic measurement of the yarn tension in winding process based on the image process technology is proposed.───为了实现卷绕机上纱线张力非接触式动态检测，提出一种基于图像处理技术的检测方法。

It is discussed how to avoid the deviation in examination and how to adjust the spinning and winding process by the examination result.───探讨了在检验过程中如何避免偏差，利用检验结果来调整优化纺丝及卷绕工艺。

英语使用场景

This product is used primarily for hand lay - up , pultrusion, RTM, and filament winding process, etc.

This paper introduces the method of fabrication of FRP nose radome by filament winding process.

Filament winding process is well suited to the manufacture of rotationally - symmetric components.

The method of design high frequency transformer in fly-back circuit in introduced in detail, besides the Transformer winding process is discussed.

The three most commonly used method of manufacturing FRP are Cross-winding process, continuous winding process and the centrifugal casting process.

According to filament winding process, a composite flywheel rotor laminated winding process was approved.